HOCHIKI – NN CONTROLS

Hochiki IR3 / IR3-IS / IR3-EX INFRA-RED Flame Detector

admin — Mon, 15 Jan 2024 16:33:04 +0000

STANDARD FEATURES
• Choices of Infra-Red Flame Detector are IR3, IR3-EX (Explosion Proof), IR3-IS (Intrinsically Safe)
• LPCB Listed and Certified to EN54-10
• Certified to II 2 G D
• Range of view up to 25m (82 ft.)
• Reduces false alarm by built-in combination filters and signal processing techniques
• Operates even if the lens is contaminated by a layer or oil, dust, water-vapor or ice

Hochiki FIRElink-100 High Sensitivity Air Sampling Smoke Detector

admin — Mon, 15 Jan 2024 16:29:05 +0000

Ultra small, low cost aspirating smoke detector for easy and discreet installation
High sensitivity provided by laser based forward light scatter for reliable early warning
Two sampling pipes up to 100 m (aggregate) in length (still air)
False alarms reduced by unique laser sensing technology – able to discriminate against dust
RS485 communications built in as standard for networking and remote communications

Hochiki FN-600ULX Power Supply/Charger

admin — Mon, 15 Jan 2024 16:25:08 +0000

STANDARD FEATURES
• Cost Effective
• Filtered and Electronically Regulated Output
• AC Fail Supervision (Form C), Low Battery Supervision (Form C) and Battery Supervision (Form C)
• Built In Charger for Sealed Lead Acid or Gel Type Batteries
• Accommodates (2) 12VDC/7AH batteries

Hochiki PE-6SN Power Extender

admin — Mon, 15 Jan 2024 16:22:09 +0000

120/240 VAC 50/60 Hz Input
PE-6SN offers 6 amps, PE-10SN offers 10 amps
Two (2) Trouble Relays
Two (2) Class A or B trigger circuit
One (1) Programmable AUX power rated @ 3 amps
Quadrasync provides panel wide synchronization of the same or multiple brands
Pass Thru mode allows the Outputs to match the Input Signal
Signal Circuit Trouble Memory – Facilitates quickly locating intermittent system trouble and eliminated costly and unnecessary service calls. LED’s indicate a prior fault (short, open, ground) has occurred on one or more signaling circuit outputs.
Horn/Strobe sync protocols include: Gentex, System Sensor, Wheelock and Amseco/Potter.
Temporal Code 3 Mode
Configurable output circuits (DIP switch sets options for each circuit)
15 mA at 8-33 VDC input trigger
Reference EOL allows 2K-27K EOL value to be used
AC fail, battery presence & low battery monitoring
Supports 7 – 55AH batteries
Accommodates up to two (2) 12VDC/18AH batteries
Power supply, logic board, red enclosure, cam lock (CAT30), transformer & battery leads

Hochiki HE Series Selectable Candela Evacuation Signals

admin — Mon, 15 Jan 2024 16:18:11 +0000

STANDARD FEATURES
• Nominal voltage 12VDC and 24VDC
• 24VDC units have field selectable candela options of 15, 30, 60, 75, and 110 candela
• 12VDC units have field selectable candela options of 15, 30, 60, and 75 candela
• Unit Dimensions: 5″ high x 4.5″ wide x 2.5″ deep
• Synchronize strobe and/or horn with Hochiki Series Control Module (12VDC product must use the HAVSM Module)
• Prewire entire system, then install signals
• Lower installation and operating costs
• Input terminals supports 12 to 18 gauge wire
• Switch selection for high or low dBA
• Switch for chime, whoop, mechanical and 2400Hz tone
• Switch for continuous or temporal 3 (not available on whoop tone)
• Surface mount with the HSB (Hochiki surface mount box)
• Silence horn while strobes remain flashing
• Wide voltage range 8-17.5VDC (12VDC units) 16-33VDC or FWR (24VDC units)
• Faceplate available in red or off-white
Product Compliance
• NFPA 72
• Americans with Disabilities Act (ADA)

Hochiki DCP-AMS SERIES Addressable Manual Pull Stations

admin — Mon, 15 Jan 2024 16:11:27 +0000

Features & Specifications

– Single and dual-action models are available

– Bi-colored status LED indicates Standby and Alarm conditions

– Address can be programmed when installed

– Key lock or hex key-lock models are available

– ADA compliant (except LP models)

Operating Voltage (SLC): 17~41 VDC
Average Current Consumption: 550uA (Typical) | 660uA (Alarm)
Ambient Temperature: 32°F (0 °C) ~ 120°F (49°C)
Maximum Humidity: 90% RH, non-condensing
Dimensions: 3.4″W x 4.8″H x 2.0″D
Mounting: Single gang or 4″ square electrical box

Hochiki DCP-CZM Conventional Zone Module

admin — Mon, 15 Jan 2024 16:05:48 +0000

Features & Specifications

– UL 864 9th Edition Listed

– Provides an address point for a zone of up to 25 conventional smoke detectors

– Blinks green when polled. Latched on red (controlled by panel) when activated

– Device address can be programmed with a handheld programmer. Device address- ranges from 1 to 127

– Compatible with Class B and Class A wiring

Supply Voltage (S-SC): 25.3 ~ 39 VDC
Auxiliary Supply Voltage: 18.8 ~ 27.2 VDC
Average Current Consumption: 670µA
2-Wire Detector Loop Current: 1mA Max.
From Auxiliary Supply: 60mA Max.
EOL Device: 4.7 ohms Resistor
Max. Quantity Per Loop: 127
Alarm Threshold Level:

Wiring Threshold Level: >2.5K ohms &

Open Circuit Threshold Level: >10K ohms

Hochiki DCP-R2ML/-I & DCP-R2MH/-I Dual Relay Module

admin — Mon, 15 Jan 2024 16:02:23 +0000

Provides two independently configurable Form C contacts per address

– Contacts are rated as follow:

+ R2ML: 2A @ 30 VDC / 0.5A @ 120 VAC

+ R2MH: 8A @ 30VDC / 4.8A @ 250 VAC

– Up to127 devices can be used on each SLC loop

– Visible Bi-colored LED is software controlled and can be programmed to blink red or green when polled. The LED can be latched on when activated. (For All Models)

– Yellow LED indicates a short circuit condition (R2ML-I & R2MH-I only)

– Programming is highly flexible providing 16 priority states plus zoning capability

– Operates on Class A or Class B SLC loop

– UL 864 Listed

Hochiki DCP-DIMM Dual Input Monitor Module

admin — Mon, 15 Jan 2024 15:50:08 +0000

Features & Specifications

– UL 864 9th Edition Listed

– Fast, reliable contact monitoring utilizing the Hochiki DCP (Digital Communications Protocol)

– 127 devices can be used per DCP loop

– Bi-colored indicating LED provides module status

– Dual input contact monitor

Supply Voltage (S-SC): 25.3 ~ 39 VDC
Average Current Consumption: 600µA (Typical) | 720µA (Alarm)
Programmable Inputs: 2 Independent Monitoring Inputs
EOL Device: 22K ohms Resistor
Max. Quantity Per Loop: 127
Dimensions: 4.2”W x 4.7”H x 1.4”D
Operating Temperature: 32°F (0°C) ~ 120°F (49°C)
Mounting: 4” square electrical box
Relative Humidity: 90% RH Non-Condensing

Hochiki ASB Analog Sounder Base

admin — Mon, 15 Jan 2024 15:47:14 +0000

STANDARD FEATURES
• Programmable evacuation codes – Continuous, March, ANSI Temporal patterns
• Base learns the sensor address and assumes an upper range address (128-254)
• Up to 127 sensors and 127 ASBs can be used on one SLC loop
• Can be alarmed or reset by zone or by individual address
• ASB SLC loop wire resistance = 50 ohms Max.(total SLC wire run length)
• High sound pressure level (85dB SPL at 10 feet)